Rheology is the study of the flow of matter, and the flow rate of 3D printing materials is fairly important when it comes to the final print. According to a pair of researchers from Massachusetts, it’s actually “the most critical material property” in terms of most polymer melt and liquid processing 3D printing processes, like FDM. It can determine the shear rate along the material flow path, influence melt temperature, create important pressure profiles, determine material output and flow rate, and even influence the final material strength and shape.
The researchers, hailing from the University of Massachusetts Lowell and Saint-Gobain Research North America, recently published a paper, titled “In-line rheological monitoring of fused deposition modeling,” about their work developing an in-line rheometer for the FDM process.
The abstract reads, “An in-line rheometer has been incorporated into a fused deposition modeling printer for the first time by designing a modified nozzle with a custom pressure transducer and a thermocouple for measuring the processed melt temperature. Additionally, volumetric flow rates and shear rates were monitored by counting the stepper motor pulses as well as the pulses from a custom filament encoder to account for filament slippage and skipped motor steps. The incorporation of the sensors and the design and development of the in-line rheometer are described; and pressures, temperatures, and viscosities within the 3D printing nozzle are presented. The in-line rheometer was validated against traditional, off-line rotational rheology and capillary rheology measurements by analyzing two polymeric materials: polycarbonate and high-impact polystyrene. A variety of rheological corrections were considered for the in-line rheometer, including entrance effects, non-Newtonian corrections, shear heating, pressure effects, and temperature fluctuations/inaccuracies. Excellent agreement was obtained between the in-line and off-line rheometers after applying the most critical corrections, which were found to be entrance effects, non-Newtonian corrections, and temperature inaccuracies. After applying the appropriate corrections, the in-line rheometer provides an accurate viscosity measurement that can be used for real-time monitoring and process control.”
In-line, or on-line, rheometers, are most often validated by applying rheological corrections, then comparing the on-line measurements to the off-line ones. These corrections are important in order to get accurate viscosity measurements, but according to the paper, “in-line rheometers have yet to be incorporated or studied on FDM to confirm the theoretical calculations or to study the influence of rheology on final properties.”
“This article describes the design of the custom pressure transducer and custom nozzle required for the in-line rheometer. The performance of the rheometer is validated against off-line rheological measurements as well as with an in-line comparison to a capillary rheometer. Finally, a variety of rheological corrections are considered and discussed, including end effects, non-Newtonian flow, viscous dissipation, pressure effects, and temperature corrections,” the researchers wrote.
The researchers did analyze viscous dissipation as well, though it was determined to be negligible and no corrections were applied to the data. A LulzBot TAZ 6 3D printer was used, and the researchers developed a new nozzle system, complete with several custom parts, to create the in-line rheometer. Both the load cell clamps and the nozzles were produced from brass castings of lost wax patterns 3D printed by Shapeways, and polycarbonate (PC) and high-impact polystyrene (HIPS) filaments were both analyzed on the in-line rheometer.
The researchers validated the in-line FDM rheometer (FDMRheo) by 3D printing into open space with a stationary nozzle raised 30 cm above the build plate. Capillary rheology (CapRheo) and rotational rheology (RotRheo) were both performed for the HIPS and PC materials. The researchers found that the FDMRheo they designed was able to provide very accurate measurements of viscosity.
“The FDMRheo can collect data across a wide range of temperatures and shear rates to generate a successful Cross-WLF model for analyzing continuous viscosity curves as a function of temperature, shear rate, and pressure. The sensor for measuring the filament feed rate as well as the thermocouple for measuring melt temperature were both critical for the deployment and accuracy of the in-line rheometer. Entrance effects were the most significant correction for obtaining an accurate viscosity, so the Bagley correction should be applied to allow the FDMRheo to be used for real-time process control of the FDM process. For example, a control scheme could be developed to optimize the printing speed while maintaining pressures and viscosities within the ideal processing window,” the researchers concluded. “The FDMRheo is suitable for analyzing the viscosity of new, 3D printable materials to more rapidly introduce new materials to the market; the vision is that the rheometer can enable automatic process optimization and quality assurance using physics-based models for weld fusion (i.e., interlayer strength), residual stress, print density, and shrinkage.”
Co-authors of the paper are Timothy J. Coogan and David O. Kazmer.
Discuss this and other 3D printing topics at 3DPrintBoard.com or share your thoughts below.