What Mother Nature has already created, we humans are bound to try and recreate; case in point: biological sensors. Thanks God to good old biomimicry, researchers have made their own artificial sensing systems based on designs already found in nature, like olfactory sensors in sharks, wake sensing whiskers in seals, thermal sensors in beetles, acoustic sensors in the inner ear, etc. Extremely sensitive cilia structures in nature perform MEMS flow sensing activities – this is why crickets can detect extremely low airflow velocities and spider legs are very sensitive to low air flow perturbation energies.
A trio of researchers from the University of Groningen and MIT recently published a paper, titled “Bioinspired Cilia Sensors with Graphene Sensing Elements Fabricated Using 3D Printing and Casting,” about their new “processing paradigm” for easier fabrication of flexible sensors that have bio-inspired structures. In the past, artificial MEMS cilia sensors were created with traditional micro/nano fabrication processes, using SU-8 polymer or silicon embedded with piezoelectric or piezoresistive sensing elements. However, these processes were rife with issues, top of the list being the lack of an ultra-sensitive material to mimic cilia.
“The proposed fabrication workflow entailed 3D-printing a metallic mold with complex and intricate 3D features such as a micropillar and a microchannel, casting polydimethylsiloxane (PDMS) inside the mold to obtain the desired structure, and drop-casting piezoresistive graphene nanoplatelets into the predesigned microchannel to form a flexible strain gauge,” the researchers wrote.
Using their novel processing methodology, Amar M. Kamat, Yutao Pei, and Ajay G.P. Kottapalli designed and created a cilia-inspired flow sensor, which used PDMS as the sensor structure and graphene nanoplatelets (GN) as the piezoresistive sensing elements. They did not physically 3D print the sensor structure; instead, they cast PDMS into a stainless steel mold, 3D printed on an SLM Solutions 125HL, to make the structure itself.
“The bioinspired sensor design comprised an all-PDMS cantilever-pillar structure with a GN piezoresistor deposited on the cantilever surface,” the researchers explained. “The drag force-induced bending of the pillar, and thereby the cantilever, due to flow was sensed by a change in resistance of the piezoresistive sensing elements (i.e., GN) located inside the microchannel.”
Once the PDMS solution was prepared, diluted conductive graphene dispersion was drop cast into the microchannel on the cantilever’s surface. Thanks to the capillary effect, the GN solution flowed easily and, once it had dried, formed a thin film on the PDMS substrate. Conductive silver paste was used to make electrical connections at the ends of the microchannel, and the GN sensing elements were then “homogeneously distributed inside the microchannel and contacted each other.”
“Since the GN strain gauge present on the top surface of the cantilever forms the fundamental piezoresistive sensing element, the determination of its gauge factor (GF) is a crucial step towards the sensor characterization,” the researchers wrote.
They conducted uniaxial tension-compression tests in order to characterize the strain gauge, and then performed oscillatory and steady-state tests in both air and water to gauge how sensitive the cilium sensor was for flow and touch stimuli.
“The graphene-on-PDMS strain gauge showed a high gauge factor of 37 as measured via cyclical tension-compression tests,” the researchers wrote.
“The sensor showed good sensitivity against both tactile and water flow stimuli, with detection thresholds as low as 12 µm in the former and 58 mm/s in the latter, demonstrating the feasibility of our method in developing flexible flow sensors.”
The measured GF (gauge factor) was pretty high, which the team says demonstrates the high potential their process has for making flexible graphene-on-PDMS strain gauges.
In addition to the team’s low-cost, repeatable method, the researchers also have other original aspects in their work, like:
- the use of GN as a piezoresistive sensing element for flow sensing
- the creation of high sensitivity in bioinspired MEMS flow sensors through flexible sensor structures and high-GF graphene sensing elements
“The fabrication methods described in this work alleviate the cumbersome and expensive multilayer deposition and lithography steps required to fabricate complex 3D structures (e.g. high-aspect ratio pillars) and/or intricate features (e.g. microchannels). The proposed methodology also allows the possibility of using a wide range of polymer materials for MEMS fabrication. Finally, the 3D printing and casting approach described in this work can potentially pave the way to the development of other biomimetic 3D-printed sensor structures in the future,” the researchers concluded.
They believe that their fabrication method is promising in terms of batch fabrication of flexible electronics. Next, the researchers will work to optimize and miniaturize their sensor’s design, in addition to improving their drop-casting method so they can achieve repeatable, uniform thin film characteristics.
Discuss this and other 3D printing topics at 3DPrintBoard.com or share your thoughts in the comments below.